5th Wheel Escaper Damon Propane Furnace Manual

The 5th Wheel Escaper Damon Propane Furnace is a high-efficiency heating system designed for recreational vehicles, featuring automatic ignition, adjustable thermostat control, multiple heat settings, safety shut-off mechanisms, and propane fuel operation. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Gas Supply 7. Operating Procedures 8. Safety Features 9. Maintenance & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Propane burner assembly, thermostat control, blower motor, heat exchanger, exhaust vent, safety shut-off valve.

Feature	Description
Propane Burner	High-efficiency combustion system
Thermostat Control	Adjustable temperature settings
Blower Motor	Distributes heated air throughout RV
Heat Exchanger	Transfers heat to air stream
Exhaust Vent	Removes combustion gases safely
Safety Shut-off Valve	Automatic gas shut-off in case of malfunction
Ignition System	Automatic electronic ignition
Multiple Heat Settings	Low, Medium, High heat output options
Air Intake	Fresh air supply for combustion
Control Panel	LED indicators and mode selection

Installation

Unpack and inspect all components. Ensure proper ventilation and clearance.

Mount furnace unit: Secure in designated compartment with proper clearance.
Connect ductwork: Attach heating ducts to outlet ports.
Install exhaust vent: Route exhaust pipe through RV wall with proper sealing.
Connect propane supply: Use approved gas line and fittings.
Wire electrical connections: Connect to 12V DC power source.

WARNING! Installation must be performed by qualified technician. Ensure proper ventilation to prevent carbon monoxide buildup.

First-Time Setup

Complete installation checks before initial operation.

Check gas connections: Test for leaks with soap solution.
Verify electrical connections: Ensure proper 12V DC power supply.
Test ignition: Turn thermostat to heat mode and verify proper ignition.
Adjust thermostat: Set desired temperature and test operation.
Check airflow: Verify proper air circulation through vents.

CAUTION! Never operate furnace without proper ventilation. Test carbon monoxide detector before use.

Specifications

Heating Capacity: 25,000-30,000 BTU/hr
Fuel Type: Liquid Propane (LP) Gas
Power Requirement: 12V DC
Ignition: Automatic electronic
Airflow: Variable speed blower
Thermostat: Digital adjustable
Exhaust: Direct vent system
Dimensions: Standard RV furnace size
Weight: Approximately 25-30 lbs
Operating Temp Range: -20°F to 120°F

Controls and Settings

Access controls via thermostat and furnace control panel.

Thermostat: POWER ON/OFF, Temperature setting, Fan mode (Auto/On), Heat level selection.

Furnace Control: Main power switch, Reset button, LED status indicators (Power, Heat, Error). Settings: Temperature range (50°F-90°F), Fan delay settings, Heat output levels (Low/Med/High). Safety: Automatic high-limit switch, Flame failure detection, Over-temperature protection.

Connecting Gas Supply

Propane tank connection and gas line installation.

Turn off all gas appliances and main propane valve.
Connect gas line using approved fittings and pipe sealant.
Open propane tank valve slowly.
Test connections for leaks with soap solution.
Check gas pressure at furnace connection point.

Tip: Always use two wrenches when connecting gas lines to prevent twisting.

Operating Procedures

Normal furnace operation and mode selection.

Power on: Turn thermostat to desired temperature above room temp.
Ignition sequence: Listen for ignition clicks and burner activation.
Heat output: Select appropriate heat level for conditions.
Fan operation: Auto mode or continuous fan operation available.
Shutdown: Turn thermostat below room temperature or use OFF position.
Emergency shutoff: Use main gas valve if needed.

WARNING! Never block air vents or exhaust ports. Maintain clearances around furnace.

Safety Features

Multiple safety systems to prevent hazardous conditions.

High Limit Switch: Shuts off burner if temperature exceeds safe limits. Flame Failure Detection: Automatically shuts off gas if flame is not detected. Pressure Switch: Ensures proper ventilation before ignition. Over-temperature Protection: Prevents furnace overheating. Carbon Monoxide Safety: Requires proper venting and regular detector testing.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and safety.

Monthly: Check and clean air filters
Seasonal: Inspect burner and heat exchanger
Annual: Professional inspection and cleaning
As needed: Clean vents and ductwork

CAUTION! Turn off power and gas supply before performing any maintenance. Use only approved replacement parts.

Regulatory Information

Certified to ANSI Z21.44 standards for RV furnaces. CSA approved for North American use. Complies with RVIA standards for recreational vehicle equipment. Copyright © 2025 Damon Corporation. For technical support, visit www.damonrv.com or contact 1-800-555-DAMON.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Furnace won't start	Power/gas supply	Check 12V power; verify propane supply; check thermostat setting.
No heat output	Ignition failure	Listen for ignition clicks; check gas valve; reset furnace.
Blower runs but no heat	Gas supply/ignition	Verify propane tank not empty; check ignition system.
Furnace cycles on/off frequently	Airflow restriction	Clean air filter; check vents for obstruction.
Unusual odors	Dust accumulation	Clean burner assembly; allow initial burn-off of manufacturing residues.
Error code displayed	System fault	Refer to error code chart in manual; reset system.

Reset Procedure: Turn thermostat off, wait 5 minutes, then restart.

Service: 1-800-555-DAMON; www.damonrv.com