amana furnace model ptc153b50aj manual reset button

The Amana PTC153B50AJ is a high-efficiency gas furnace with a manual reset button for safety and operational control. The reset button is a critical safety feature that shuts down the furnace when it detects potential issues such as overheating, ignition failure, or other system malfunctions. Below are key sections covering safety precautions, reset button location, reset procedures, troubleshooting, and maintenance guidelines.

1. Safety Precautions 2. Reset Button Location 3. Reset Procedure 4. Troubleshooting Common Issues 5. Maintenance Guidelines 6. Specifications 7. When to Call a Professional 8. Warranty Information 9. Regulatory Compliance

Safety Precautions

Before attempting to reset the furnace, ensure you follow these safety guidelines to prevent injury or damage to the unit.

Precaution	Description
Power Disconnect	Turn off electrical power at the circuit breaker before accessing the furnace
Gas Valve	Ensure gas supply valve is in OFF position before resetting
Ventilation	Check for proper ventilation and clear any obstructions
Carbon Monoxide	Install and maintain CO detectors near furnace area
Professional Help	Contact qualified technician if reset button trips repeatedly

Reset Button Location

The manual reset button is typically located on the furnace control board or near the blower compartment.

Open furnace access panel: Remove screws and carefully lift panel.
Locate control board: Identify the circuit board with LED indicators.
Find reset button: Look for red or yellow button labeled "RESET" or with reset symbol.
Identify LED codes: Note any flashing patterns for diagnostic purposes.

WARNING! Always disconnect power before accessing internal components. High voltage present.

Reset Procedure

Follow these steps carefully to reset your Amana PTC153B50AJ furnace.

Turn off thermostat: Set to lowest temperature setting or OFF position.
Cut power: Switch off circuit breaker supplying furnace.
Wait 30 seconds: Allow system to fully power down.
Locate reset button: Refer to location section above.
Press reset: Firmly push and hold reset button for 3-5 seconds.
Restore power: Turn circuit breaker back ON.
Reset thermostat: Return to desired temperature setting.

CAUTION! If reset button won't stay engaged or trips immediately, do not force it. Contact professional service.

Troubleshooting Common Issues

Reset Button Trips Repeatedly: Indicates underlying system issue requiring professional diagnosis
No Heat After Reset: Check thermostat settings, gas supply, and power connection
Furnace Won't Ignite: Verify gas valve position and pilot light status
Unusual Noises: May indicate mechanical issues with blower or burners
Error Codes: Refer to control board LED patterns for specific fault indications

Maintenance Guidelines

Regular maintenance can prevent unnecessary reset button activations.

Monthly: Check air filters and replace if dirty. Ensure vents are unobstructed.

Seasonal: Professional inspection before heating season. Clean burners and heat exchanger.

Annual: Complete system check by qualified HVAC technician.

Specifications

Model: PTC153B50AJ
Fuel Type: Natural Gas
BTU Input: 153,000 BTU/h
Efficiency: 95% AFUE
Voltage: 120V AC, 60Hz
Control System: Electronic ignition with safety reset
Warranty: Limited lifetime heat exchanger warranty

When to Call a Professional

Contact qualified HVAC technician if you experience any of the following:

Reset button trips more than once in 24 hours
Gas odor detected near furnace
Unusual sounds (banging, scraping, whistling)
Visible damage to components or wiring
Error codes you cannot resolve

Tip: Keep model number and serial number handy when calling for service.

Warranty Information

Amana PTC153B50AJ comes with limited warranty coverage. Register product for full warranty benefits.

Heat Exchanger: Limited lifetime warranty

Parts: 10-year limited warranty

Labor: 1-year limited warranty

For warranty claims: Contact Amana customer service at 1-888-292-6262 or visit www.amana-hac.com

Regulatory Compliance

This furnace complies with ANSI Z21.47 standards for gas-fired central furnaces. UL listed and meets all applicable safety standards. Manufactured to Amana quality specifications. For technical support and service, contact authorized Amana dealers only.