Fahrenheit 50 Pellet Furnace Manual

The Fahrenheit 50 Pellet Furnace is a high-efficiency heating system designed for residential use, featuring automatic pellet feed, digital thermostat control, ash removal system, safety sensors, and energy-saving modes. With a heating capacity of up to 50,000 BTU/hr, this furnace operates on wood pellets and includes features such as programmable timers, temperature settings, maintenance alerts, and compatibility with standard venting systems. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Fuel and Loading 7. Operation 8. Maintenance 9. Safety Features 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Digital control panel, pellet hopper, combustion chamber, ash drawer, exhaust vent, safety sensors, and thermostat connection.

Feature	Description
Digital Control Panel	For temperature settings, timer, and mode selection
Pellet Hopper	Holds up to 40 lbs of wood pellets
Combustion Chamber	High-efficiency burn system with ceramic lining
Ash Drawer	Easy-remove container for ash disposal
Exhaust Vent	Standard 3-inch vent for smoke output
Safety Sensors	Overheat protection and low pellet detection
Thermostat Connection	Compatible with standard home thermostats
Power Switch	Turns furnace on/off
Mode Selector	Auto, Manual, and Economy modes
Maintenance Alert	LED indicator for cleaning and service needs

Installation

Unpack and inspect contents. Place on level, non-combustible surface.

Position furnace: Ensure clearance of 36 inches from combustible materials.
Connect venting: Attach 3-inch exhaust vent to exterior; use approved materials.
Install thermostat: Wire to control panel following diagram.
Plug into dedicated 120V AC outlet.
Fill hopper with pellets; perform initial ignition test.

WARNING! Furnace must be installed by qualified technician. Ensure proper venting to prevent carbon monoxide buildup.

First-Time Setup

Power on furnace; follow startup sequence.

Set mode: Press MODE to select AUTO for thermostat control.
Program timer: Use TIMER button to set daily on/off cycles.
Adjust temperature: Set desired temp via control panel or thermostat.
Test ignition: Press IGNITE; wait for flame establishment.
Check venting: Ensure smoke is exiting properly.

CAUTION! Do not block air intakes or exhaust. Keep children and pets away during operation.

Specifications

Heating Capacity: 50,000 BTU/hr.
Fuel Type: Wood pellets (premium grade recommended).
Hopper Capacity: 40 lbs.
Efficiency: 85% AFUE.
Venting: 3-inch standard exhaust.
Power Requirements: 120V AC, 60Hz.
Thermostat: Compatible with most 24V systems.
Dimensions: 36" H x 24" W x 28" D.
Weight: 150 lbs.

Controls and Settings

Access settings via digital control panel. Buttons: POWER, MODE, TEMP UP/DOWN, TIMER, IGNITE, RESET.

Remote Thermostat: Set temperature; furnace responds automatically in AUTO mode.

Modes: AUTO (thermostat-controlled), MANUAL (constant burn), ECONOMY (reduced pellet feed). Settings: Temperature range 60°F–85°F, timer programs, maintenance alerts. Safety: Overheat shutdown, low pellet sensor, flame-out protection.

Fuel and Loading

Use only premium wood pellets; avoid wet or contaminated fuel.

Open hopper lid; fill with pellets to maximum line.
Close lid securely to maintain air seal.
Check pellet level via window indicator.
Refill when low pellet alert activates.

Tip: Store pellets in dry area to prevent moisture damage.

Operation

Supports continuous heating with automatic pellet feed.

Startup: Press POWER, then IGNITE; wait for ignition cycle.
Adjust settings: Use MODE for operation type; TEMP for desired heat.
Monitor: Check flame via viewing window; ensure steady burn.
Shutdown: Press POWER to initiate cool-down cycle.
Emergency stop: Use circuit breaker for immediate power cutoff.

WARNING! Never use gasoline or accelerants. Do not open combustion chamber during operation.

Maintenance

Regular cleaning ensures efficiency and safety.

Daily: Empty ash drawer when full.
Weekly: Clean burn pot and heat exchanger.
Monthly: Inspect and clean venting system.
Annually: Professional service recommended.

CAUTION! Always turn off and unplug before maintenance. Wear gloves when handling ash.

Safety Features

Overheat Protection: Shuts down if temperature exceeds safe limits. Low Pellet Sensor: Alerts when fuel is low. Flame-Out Protection: Stops pellet feed if flame extinguishes. Carbon Monoxide Detector: Compatible with external CO alarms.

Regulatory Information

UL Certified: Meets safety standards for residential heating appliances. EPA Phase II: Compliant with emission requirements. Copyright © 2025 Fahrenheit Heating Systems; trademarks of Fahrenheit Inc. For support, visit www.fahrenheitheating.com or contact 1-800-555-HEAT.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No ignition	Empty hopper/wet pellets	Refill with dry pellets; check ignition element.
Low heat output	Dirty burn pot/airflow	Clean burn pot; ensure vents are clear.
Furnace shuts off	Overheat/blocked vent	Check for obstructions; allow cool-down.
Ash buildup	Full ash drawer	Empty drawer; clean combustion area.
Error code on display	Sensor fault	Refer to code chart in manual; reset if needed.

Reset: Press RESET button on control panel.

Service: 1-800-555-HEAT; www.fahrenheitheating.com